NEW TNA 3-GUN VR-66 12ga SHOTGUN is here!

I say buy, I have one and it's an excellent gun for the money, I'd put it in league with semi's at 2x the price. It's no 2k shotgun but it is a great value for a semi.
 
Kimo62 said:
Any lefties using this? looking for feedback good bad or ugly.
Click to expand...
Yes, I’m a lefty and I’m quite impressed with this shotgun. I’ve used it in a few 2Gun and 3Gun competitions and it has been flawless. Super easy to quad load, light, manoeuvrable and reliable so far. I’ve probably got 6-700 rounds thru it now, so not a huge amount but it has been excellent so far and very lefty friendly. I’ve also shot a few rounds of Trap with it just for fun 😊
 
I Dont Care About You said:
Mag capacity is a make or break deal for me. I'd consider this shotgun if it has a 5+1 capacity. Otherwise its a no-go for me.
Click to expand...
I talked to a VR-66 owner about this because I was also wondering. TNA's info is not clear at all on this. He said the +2 extension allows 5.X rounds of 3", which equates to 6 rounds of 2.75". You can ghost load as well, for a total capacity of 6+1+1 with 2.75" shells.


Mark
 
mmattockx said:
I talked to a VR-66 owner about this because I was also wondering. TNA's info is not clear at all on this. He said the +2 extension allows 5.X rounds of 3", which equates to 6 rounds of 2.75". You can ghost load as well, for a total capacity of 6+1+1 with 2.75" shells.


Mark
Click to expand...
I'm not sure this is correct. I've got the 2+ mag extension on mine and it will fit 5 +1 +1 (2.75" shells)
 
This gun is really diverting my interest away from the M3K. Much prefer the 18.6" barrel on the VR-66 versus the 24" on the M3K. Also from what I've read, the VR-66 is an actual M2 clone, versus the M3K being "M2-ish". The M3K uses AN inertia setup, but the layout is totally different than Benelli system.

Benelli's engineering of these guns is obviously brilliant, so the VR-66 being an actual clone is more appealing to me.

We need more people doing YouTube vids on these new guns.
 
I confirmed on mine: 5 x 2 3/4 in the magazine. +1 + 1.

Not sure how people are getting 5+ in the mag.

I’ve got he TNA extension.
 
CanuckShooter said:
This gun is really diverting my interest away from the M3K. Much prefer the 18.6" barrel on the VR-66 versus the 24" on the M3K. Also from what I've read, the VR-66 is an actual M2 clone, versus the M3K being "M2-ish". The M3K uses AN inertia setup, but the layout is totally different than Benelli system.

Benelli's engineering of these guns is obviously brilliant, so the VR-66 being an actual clone is more appealing to me.

We need more people doing YouTube vids on these new guns.
Click to expand...
I’ve got the M3k, VR-66, and the M2 speed - for inertia shotguns.

Nothing can beat the M2 speed for quality.

They’re surprisingly close tho.
 
JeffMan said:
I’ve got the M3k, VR-66, and the M2 speed - for inertia shotguns.

Nothing can beat the M2 speed for quality.

They’re surprisingly close tho.
Click to expand...
I was looking at the A300 and the 1301 but they are WAY more expensive.

IF the VR-66 is really as good as you suggest, it would be the deal of the century at the price TNA is asking.
 
JeffMan said:
I confirmed on mine: 5 x 2 3/4 in the magazine. +1 + 1.

Not sure how people are getting 5+ in the mag.

I’ve got he TNA extension.
Click to expand...

Could be the mag spring being lighter on one or the other.

If you have an extra spring lying around try to remove a few coils and maybe shorten up the follower a bit if possible. Of course always be sure it can't fit more than 5 3in shells at all times .

Also most 2 and 3/4 shells are 2.5" or even slightly less, maybe yours are a little longer.
 
I Dont Care About You said:
Are these two different mag extensions?
Click to expand...
That’s entirely possible. I’m using the extension that comes with the VR.

As another user pointed out - The shells I tested capacity with may be a bit longer, but the same shells in my M2 Speed, with its included extension give me 6 + 1 + 1 (with the bolt mod)

Also of note; the VR-66 looks to be on sale today, while I’m fairly certain it was full price yesterday.
 
Likely your spring is long. Mine came with the +2 extension and included a longer spring for it. I used the original spring and can get 6 2 3/4's shells in there but not over 5 3"ers
I also bought their +3 extension which is flush (looks goood) to the barrel, it is blocked to 5.9 3" shells. Not sure what it would hold for 2 23/4"s unblocked but I'm sure I could do some measuring and figure it out if anyone is interested.
 
GimpyGolden said:
Likely your spring is long. Mine came with the +2 extension and included a longer spring for it. I used the original spring and can get 6 2 3/4's shells in there but not over 5 3"ers
I also bought their +3 extension which is flush (looks goood) to the barrel, it is blocked to 5.9 3" shells. Not sure what it would hold for 2 23/4"s unblocked but I'm sure I could do some measuring and figure it out if anyone is interested.
Click to expand...
I'd like to get the plus 3.

Was it from TNA?

EDIT: I see they have the +3 in stock. ORDERED.
 
Last edited:
JeffMan said:
That’s entirely possible. I’m using the extension that comes with the VR.

As another user pointed out - The shells I tested capacity with may be a bit longer, but the same shells in my M2 Speed, with its included extension give me 6 + 1 + 1 (with the bolt mod)

Also of note; the VR-66 looks to be on sale today, while I’m fairly certain it was full price yesterday.
Click to expand...
How close are you to getting 6 rounds in? It may only need a small bit of tweaking to get there.

It was on sale yesterday when I looked at TNA's site.


Mark
 
You must log in or register to reply here.
Back
Top Bottom