The "What Have You Reloaded Today" thread

[hoytcanon]

Just ran 200 pieces of 8mm Mauser brass through a custom die set to create 7.62X57 brass (Medium Mauser? ??)... in preparation for the new arrival.

Also prepped and light-loaded, 200 pieces of 6mm Rem brass preparing to fireform to 6mm S.I (Slightly Improved).

Loaded 100 .358 Win with 225 Partitions in a Max loading as a shoulder carry in coastal bear country.

And 100 rounds each with two powders to ladder test with a pair of Ruger No.1-RSI in .257 Roberts and 7X57 Mauser to do a little post season tweaking.

Also, 100 rounds of .218 Bee with 14 gr. LG under 40 VM'S just so I can giggle like a little girl.

 

[tbrwlf]

12 Gauge Magtech Brass, Large rifle primers, 80 gr FF BP, overpowder nitro card, plastic wad, 1 oz # 6 shot, overshot clear plastic disc, roll crimp in RCBS cowboy dies.

26 loaded and ready for my old Husqvarna.

recently 6.5x55 .223

 

[TheM4chef]

I finished 200 124gr campro rn 9mm this morning.
Did 75 of my 168gr 308's before that and I'm hoping my H110 shows up tomorrow so I can start on my 300blk reloading

 

[MC One Shot]

Resized and primed 100 38-55 and 100 45-90 cases
Sized and lubed .380 255gr, 100 .360 535gr cast bullets
Measured 200 loads of FFG for above

 

[cr5]

My god, I hate processing 223 brass. Trimming and then deburring/chamfer makes my hands cramp up. I need to start shooting larger calibers that are easier to grip. lol

Same here. I prepped 50 pieces of 300BLK the other day and my hands were pretty sore by the end.

I loaded up 10 rounds of 300BLK with 150gr FMJ and 6.3gr of Trailboss for a cool little subsonic load for the bolt action. They don't cycle the AR or ACR but are fun 50yd gong bangers in my Rem700 that won't p!ss off the neighbors. No, you won't find data for that load anywhere, a buddy with years of 300BLK experience made that one up and shared with me.
I still need to do a little experimenting with the load and the chrony to fine tune it to the Rem700 but it looks good so far

 

[leadchucker62]

17 hornady hornet
222 remington
30 remington
and 35 remington with the new lee 200gr cast boolit.

Now to go and have some fun
Z

 

[bcnorth]

Special on todays menu.
44mag shotshells

 

[Trinimon]

Special on todays menu.
44mag shotshells

Do tell.

 

[cr5]

Special on todays menu.
44mag shotshells

Do tell.

Is that a 44mag brass with 2 44 cal balls shoved in over a powder charge? Scary and exciting all at the same time

 

[Garand]

Spent the day resizing and belling both .38-55 & 9mm.

 

[Hunter1970]

I'm still beating up about 10 gallons (yes, GALLONS) of 223. Just trying to get them all prepped. Still working on the FL sizing. It's going to be a long winter...

 

[cheaplaughs]

10 rnds of 260 rem for my new to me rem 700 custom

 

[JJ-65]

Mass produced some .257 Roberts ammo for a new Kimber select that wont shoot any better than the mid .3s @ 100yds. Must have got a bad one again. Lol.

 

[terry_g]

Loaded 20 45-70 for my 1895 marlin.
350 grain Berry's bullets 40 grains oh H4198 and RP brass.
An accurate moderate recoil load.


Terry

 

[bcnorth]

Do tell.

303 cut down filled with rat shot and 6gr of titewad

 

[laker415]

Prepped and primed 50 223 brass. Just heading to the garage load some 55 gr varmageddon over some H335.

 

[Trinimon]

303 cut down filled with rat shot and 6gr of titewad

Cool! Sounds like a hoot. I'll have to keep that in mind next time.

 

[madashell]

No assembling but purchased some Varget and CC1 #34's.

 

[The Cold Lake Kid]

Finished dry tumbling, de-priming, then sonic tumbling a few thousand empty .45 Colt cases, from last summer's CAS season. Great fun!
I'll reload them over the winter and get them ready for next season.
Once they're done, it'll be on to loading for my .45-70's (I have 4 single shots)

 

[daBear]

Just did a couple hundred 10mm and 400Corbon..Now to test them...